2020-2023 TOYOTA GR SUPRA - Tail Light Face Tint Overlay

Finding a way to tint your Supra Tail Lights at home without being a professional may be hard, but with this product specifically designed for the face of your tail light, anyone can tint them, even if you're a beginner. With a little bit of patience and the right tools that we have here on our site, such as our Pro Felt Squeegee you can change the entire look of your rear end yourself in under 30 minutes.

If you want to take it a step further you can couple this product with our Tail Light Deck Overlay to truly make your Supra Stand out even more. Our overlays are computer precision cut into durable automotive grade vinyl. This product covers only the face of your tail light making installation very easy. Unlike most ebay or amazon vendors, Premium Auto Styling vinyl overlays are designed and produced here in the USA in our own facility. We design and test fit all products to ensure a perfect fitment guaranteeing you the best results . Basically, if they don’t work on our cars, they’re not going to end up on yours. If you are looking for an inexpensive styling modification, or you just want to change up the factory look, this is a very easy way to do it without needing professional help. 

>> SOLD AS A SET :  THIS KIT INCLUDES DRIVER AND PASSENGER SIDE - MID SMOKE TINT OVERLAYS

NOTE: If you purchase this product as well as the Tail Light Deck Product, Install the Tail Light Face Overlay FIRST. Then install the Tail Light Deck Overlay SECOND.

INSTALL GUIDE

TOOLS REQUIRED: PRO FELT SQUEEGEE, HEAT GUN OR SUNNY DAY FOR POST HEAT PROCESS

DRY INSTALL: Getting the tint installed on your Supra just got easier with our special high grade tint material made to be a dry install instead of a wet install like other products. For Best results we recommend cleaning the surface that you'll be applying our overlays too, cleaning should consist of removal of any waxes, dirt and or debris. For the cleaning process a clay bar is highly recommended: CLEANING PREP SPRAY & CLAY BAR's SOLD HERE). Before you begin installation of any vinyl overlays please make sure you are working in the right conditions, you should never install vinyl in direct sunlight, never apply vinyl in temperatures that are neither too hot nor too cold. Our in-house expert installers say the optimum temperature for installing vinyl is between 65 and 72 degrees (F). Vinyl can be installed in temperatures as low as 65 degrees (F), and up to 90 degrees (F). Vinyl has a more difficult time conforming and staying in place in colder temperatures though, which is why we recommend waiting until temperatures warm up or install in a temperature controlled environment.

NEXT after making sure your tail light is clear of debris and any moisture, remember this is a dry install not a wet install, Peel the overlay from the backing paper, hold the overlay by the inner corner that faces the trunk and the upper top corner on the opposite side shown in (Example A). This hand positioning will help with your placement.

As shown in (Example B) start by placing the inner corner on the tail light while being careful not to let the entire face of the overlay stick to the tail light just yet. Then without pulling or causing any tension on the material, simply keeping the material taught, line up the top edge of the overlay to the top edge of the tail light face up until the top right corner your other hand is holding as shown in (Example C).

If you end up with a horizontal wrinkle on the face of the overlay such as the one shown in (Example D) simply pull that section back up and re-lay it again without tension to avoid getting that wrinkle again.

Once the top edge, inner and top outer corner is aligned correctly without any tension, As Shown in (Example E) squeegee down the face of the overlay starting from the inner corner moving towards the outer side of the tail light. Stop when you get to the area shown in (Example F).

Now shift your focus to the side portion of the tail light, position your squeegee vertically as show in (Example G) while holding the remaining material away from the tail light, in one motion gradually lay the material down onto the tail light as you are squeegeeing it down in one motion. 

Switch to the hard side of your squeegee as shown in (Example H) tuck the remaining portion of the overlay into the crevasse between the tail light and rear quarter panel to achieve full coverage.

With your finger lay the outer edges of the overlay conforming nicely over the curved edge. (Example I).

Go back over the entire product with your squeegee to make sure there is no remaining air underneath the material. Finish by post heating the material with a heat gun or by leaving the vehicle outside on a warm sunny day for a couple of hours. This is done to finish the adhering process, and help conform any beveled edges. Once this is done your install is complete. We recommend combining this product with our Tail Light Deck Black Out Overlay in Gloss Black - or - Carbon Fiber.

NOTE: If you purchase this product as well as the Tail Light Deck Product, Install the Tail Light Face Overlay FIRST. Then install the Tail Light Deck Overlay SECOND.

SUPERIOR QUALITY 

• Adhesive backed film for easy installation and removal.  
• Maintenance free & car wash safe. 
• Can be removed without any damage to surface. 
• 1-3 year life expectancy.  

>> DISCLAIMER INFORMATION 

DIFFICULTY RATING 3/5

 MORE >> Difficulty Rating Information