2017–2021 Honda Civic Hatchback & Type R Tail Light Smoked Tint Overlays
Give your Honda Civic Hatchback or FK8 Type R a darker rear-end detail with precision-cut smoked taillight tint overlays. This two-piece kit tones down the designated taillight insert areas, creating a more understated appearance without replacing the factory light assemblies.
Smoked Tint FinishDarkens the covered insert sections for a subtle, custom taillight appearance.
Pre-Cut FitmentShaped for the intended 2017–2021 Civic Hatchback and Type R taillight insert locations.
Driver + Passenger SetIncludes two overlays to complete the matching left and right application areas.
A Small Detail. A Darker Look.
Add Contrast to Your Civic’s Taillights
Change the appearance of the contrasting insert sections within your factory Civic taillights. Premium Auto Styling smoked tint overlays darken these areas while leaving the surrounding lens sections uncovered, creating a focused styling accent rather than a fully tinted taillight.
Each piece is precision-cut from adhesive-backed smoked tint vinyl for the designated insert area shown in the product images.
Translucent smoked vinyl tint finish
Pre-cut taillight insert overlays
Two-piece kit with driver-side and passenger-side coverage
Designed for compatible 2017–2021 Honda Civic Hatchback and FK8 Type R taillights
Applies over the existing lens surfaces
Wet application using a light soap-and-water mist
Installation video guide included below
Package Contents
What You Will Receive
One driver-side pre-cut smoked taillight tint insert overlay
One passenger-side pre-cut smoked taillight tint insert overlay
Sold as a two-piece set. Replacement taillight assemblies are not included.
Vehicle Compatibility
2017–2021 Civic Hatchback & Type R Fitment
2017 Honda Civic Hatchback / Civic Type R FK8
2018 Honda Civic Hatchback / Civic Type R FK8
2019 Honda Civic Hatchback / Civic Type R FK8
2020 Honda Civic Hatchback / Civic Type R FK8
2021 Honda Civic Hatchback / Civic Type R FK8
Hatchback Taillight Configuration Required
Compare your factory taillights with the product images before ordering. This listing is for the Hatchback and FK8 Type R application, not Civic Sedan or Coupe taillights. Aftermarket lights or modified lens configurations may affect fitment.
DIY Installation Video
Watch Before You Install
Review the installation guide before removing the backing. Familiarize yourself with the overlay placement, light application mist, and squeegee technique before beginning.
The same preparation and application process applies to the red and smoked versions of this taillight insert overlay kit.
Recommended supplies: A spray bottle with a light soap-and-water solution, a felt-edge squeegee, and a clean microfiber towel.
Prepare the taillights. Clean the intended application areas thoroughly. Remove dirt, wax, dressing, and residue using a cleaner compatible with the lenses.
Identify and lightly mist. Match each piece to the correct side. Remove the backing and lightly mist the adhesive side with the soap-and-water solution.
Position the overlay. Align the film with the designated insert area. Confirm the perimeter and any cutouts are positioned correctly before applying firm pressure.
Squeegee out moisture. Work from the center toward the edges using controlled pressure to remove application fluid and trapped air.
Inspect and allow to dry. Check the edges and allow remaining moisture to dry before washing. Gentle, controlled heat may help with contours when needed; avoid overheating the film or lens.
A Quick Styling Project
Application can take approximately 10 minutes once the lenses are prepared. Allow additional time for cleaning, careful alignment, and drying. Installation time varies with experience and conditions.
Keep the Finish Looking Clean
Care After Installation
Allow the film to dry and adhere before washing.
Clean with lens-compatible wash products and a soft microfiber towel.
Avoid directing high-pressure water at the overlay edges.
Do not pick at the film or use abrasive cleaning tools.
Inspect the edges periodically and use care during future removal.
Premium Auto Styling · Riverside, California
Support for Your Civic Styling Project
Have a question about taillight fitment or overlay placement? Contact Premium Auto Styling in Riverside, California, for guidance before installing your smoked tint overlays.
Add the pre-cut driver and passenger set to your cart and customize your 2017–2021 Honda Civic Hatchback or FK8 Type R with smoked taillight tint overlays from Premium Auto Styling.
Fitment and lighting disclaimer: This is an aftermarket vinyl tint-overlay product. Smoked tint reduces light transmission and may affect the visibility of covered lights or reflector performance. Confirm applicable lighting requirements before installation. Compatibility is based on the factory taillight configuration shown in the product images. Tint does not repair cracked or damaged lenses. Adhesion, service life, and removal results depend on lens condition, preparation, installation, and exposure. Honda, Civic, Type R, and FK8 names are used solely to identify vehicle compatibility. Premium Auto Styling is not affiliated with or endorsed by Honda.
These tints look really nice and is not too dark. Cutout is also precise and is not hard to install. I highly recommend these for those with oem tail lights.
s
scott K.
10th gen civic hatchback
Great product ,fit perfect and easy to apply.fast delivery and communication
