Give your 2022–2026 Subaru WRX a darker, more aggressive rear-end
appearance with our precision-cut Rear Fender Reflector Tint Overlays in
Smoke Tint. These overlays darken the factory rear bumper reflectors while
allowing their reflective appearance to remain visible.
Each overlay is pre-cut specifically for the factory reflector shape, allowing for a
clean installation with no trimming required. The smoked finish blends
naturally with darker styling themes and helps create a cleaner, more cohesive rear
bumper appearance.
WRX Rear Reflector Tint Overlays
✓ Darkens the factory rear fender reflectors
✓ Creates a cleaner, more aggressive rear appearance
✓ Smoke-tint automotive-grade film
✓ Allows the reflector’s appearance to remain visible
✓ Precision-cut with no trimming required
✓ Includes driver-side and passenger-side overlays
✓ Easy, beginner-friendly DIY installation
✓ Designed, tested and produced at our USA facility
What’s Included
-
One driver-side rear fender reflector tint overlay
-
One passenger-side rear fender reflector tint overlay
-
Complete two-piece smoke-tint overlay kit
Vehicle Fitment
Designed for the factory rear fender reflectors on the
2022–2026 Subaru WRX. Please confirm your vehicle year and factory
reflector design before ordering. This product includes tint overlays only and does
not include replacement reflectors.
Smoke Tint Finish
The smoke-tint finish reduces the bright appearance of the factory reflectors while
maintaining a visible reflective surface. It pairs especially well with dark paint,
tinted tail lights, black trim and other rear-end styling upgrades.
Designed, Tested & Produced in the USA
Premium Auto Styling overlays are computer-cut from high-quality automotive-grade
film at our own USA facility. Every vehicle-specific product is designed and
test-fitted on real vehicles to help provide accurate fitment and dependable
installation results.
Features & Specifications
-
Fits 2022–2026 Subaru WRX
-
Smoke-tint rear fender reflector overlays
-
Precision-cut for the factory reflector shape
-
No trimming required
-
Includes driver-side and passenger-side overlays
-
Complete two-piece kit
-
Allows the reflector’s appearance to remain visible
-
Durable automotive-grade tint-film construction
-
Adhesive-backed film for easy installation and removal
-
May help visually reduce the appearance of minor surface imperfections
-
Low-maintenance and automatic-car-wash safe after fully cured
-
Removes cleanly without permanently modifying the factory reflectors
-
Estimated outdoor durability of 2–5 years depending on climate, exposure,
installation and maintenance
Installation Guide
This is a simple DIY installation that requires minimal tools. Proper surface
preparation and careful alignment will help produce the best finished appearance.
Recommended Tools
-
Felt-edge application squeegee
-
Vinyl-safe surface-preparation cleaner
-
Clean microfiber towels
-
Heat gun or hair dryer for light finishing heat
Step 1: Clean the Reflectors
Thoroughly clean each reflector to remove dirt, wax, ceramic products, road film and
other contaminants. Complete the final cleaning step with a vinyl-safe preparation
solution, then allow the surface to dry completely.
Step 2: Check the Installation Conditions
Work in a clean, shaded area. Do not apply the film in direct sunlight or to a hot,
cold or wet surface. For the best results, install between
65°F and 80°F.
Step 3: Identify and Test-Fit
Identify the driver-side and passenger-side overlays before removing the backing.
Hold each piece over its corresponding reflector to confirm its orientation and
alignment.
Step 4: Position the Overlay
Peel back a small portion of the release liner and lightly position the overlay.
Confirm that the edges align evenly with the factory reflector before applying
full pressure.
Step 5: Apply the Film
Use controlled, overlapping squeegee strokes from the center toward the outer edges.
Gradually remove the remaining release liner while pressing the film into place to
minimize trapped air.
Step 6: Secure the Edges
Inspect the finished installation for bubbles or loose edges. Apply gentle finishing
heat if necessary, then firmly press around the entire perimeter. Avoid washing the
vehicle or exposing the overlays to unnecessary moisture for at least 24 hours.
No Trimming Required
Each overlay is pre-cut to match the factory rear fender reflector. When properly
aligned, no trimming or permanent vehicle modification is required.
Installation Difficulty: 1/5
A beginner-friendly installation suitable for first-time DIY installers. Clean the
reflectors thoroughly, confirm your alignment and apply the overlays carefully—piece
of cake.
Show Us Your WRX
Share a photo of your completed installation and tag
@premiumautostyling
on Instagram.
Looking for a Custom Finish?
Interested in a different color or finish? Contact our team at
orders@premiumautostyling.com
before ordering so we can review your request.
Product Disclaimer
This product is a tint-film overlay designed to cover the existing factory rear
reflectors. It is not a replacement reflector or paint protection film. Tint film
may reduce or alter reflector visibility and performance. Customers are responsible
for confirming compliance with all applicable state and local vehicle-lighting and
reflector laws before installation or use on public roads. Product appearance may
vary depending on lighting, viewing angle and screen settings.
