Have questions?
888-637-0055
Ask an Experts-
Guaranteed Fitment
Designed and tested in-house
-
In-House Experts
We know our products
-
Pre-Cut Products
DIY friendly installation
-
Wordwide Delivery
Free USA Shipping over $49
Full Mtn. Range Quarter Window Decal | 2018-2022 Subaru Crosstrek
Notice: This is a custom product that takes time to produce. If this product is in addition to your order you can expect a 3-5 day production delay. We do try to get these flag decals out as soon as possible but please be patient with us.
2018-2022 Subaru Crosstrek - Full Mtn. Range Rear Quarter Window Decal Set
Show off this Full Mtn. Range decals that is pre-cut to the rear quarter window while the decal itself is reverse cut! Making it so the sun shines through only the logo itself. This Rear Quarter Window Decal set takes your 2018+ Subaru Crosstrek un-used quarter window and turns it into a great focal point with this awesome subaru inspired decal. Even better, when sun shines through it, it casts a pretty cool shadow inside the car. It comes in a satin black OR satin grey finish that adds just the right amount of "cool factor" without being too flashy or in-your-face. Unlike most ebay or amazon vendors, Premium Auto Styling vinyl overlays are designed and produced here in the USA in our own facility. We design and test fit all products to ensure fitment guaranteeing you the best results . Basically, if they don’t work on our cars, they’re not going to end up on yours.
Color Shown in Product Image is Satin Black
INSTALL GUIDE
*MINOR TRIMMING MAY BE REQUIRED DEPENDING ON PLACEMENT OF PRODUCT. PRODUCT WAS CREATED WITH 2-3mm GAP AROUND THE OUTER EDGE OF THE WINDOW TO REDUCE THE CHANCE OF MISPLACING THE PRODUCT CAUSING OVERAGE AND REQUIRING TRIMMING. THIS GAP IS VISIBLE IN THE PRODUCT PHOTOS ABOVE.
TOOLS REQUIRED: PRO FELT SQUEEGEE
PART 1 - DRY INSTALL: Getting the vinyl installed on your vehicle is very easy and only requires minimal tools. For Best results we recommend cleaning the surface that you'll be applying our overlays too, cleaning should consist of removal of any waxes, dirt and or debris. For the cleaning process a clay bar is highly recommended: CLEANING PREP SPRAY & CLAY BAR's SOLD HERE). Before you begin installation of any vinyl overlays please make sure you are working in the right conditions, you should never install vinyl in direct sunlight, never apply vinyl in temperatures that are neither too hot nor too cold. Our in-house expert installers say the optimum temperature for installing vinyl is between 65 and 72 degrees (F). Vinyl can be installed in temperatures as low as 65 degrees (F), and up to 90 degrees (F). Vinyl has a more difficult time conforming and staying in place in colder temperatures though, which is why we recommend waiting until temperatures warm up or install in a temperature controlled environment.
PART 2 - After part 1 is complete, you can move onto part 2.
Hold the product up to the window so you can get a sense of placement before getting ready to place.
Remove product from the backing paper with the paper transfer tape attached to the vinyl. Do not peel the paper transfer tape at this time. Hold the paper transfer tape by the outer corners and align the product to the outer edge of the window.
Place the vinyl down flat, and use firm pressure with a squeegee to remove any and all air from underneath the vinyl and transfer tape. Continue until the vinyl is visibly embossed in the transfer tape, only then can you move onto peeling.
Once accomplished, start with one corner of the transfer tape and peel it back on itself slowly. This will reduce the chance of the vinyl peeling up as you remove it.
If any of the vinyl does not release from the transfer tape as you are peeling it STOP immediately, place that section back down, squeegee the area again firmly, and then continue peeling again.
If Part 1 of the install is not done thoroughly enough this can effect how well the adhesive sticks to the surface of the window which is why it is so important to do that step.
After the transfer tape is fully removed your install is complete.
SPECIFICATIONS
• Automotive Grade Adhesive backed vinyl with air release technology for easy installation and removal.
• Car wash safe.
• Can be removed without any damage to surface.
• 1-3 year life expectancy.
• Check your local laws and regulations
DIFFICULTY RATING: 3/5
MORE >> Difficulty Rating Information