Have questions?

  • Guaranteed Fitment

    Designed and tested in-house

  • In-House Experts

    We know our products

  • Pre-Cut Products

    DIY friendly installation

  • Wordwide Delivery

    Free USA Shipping over $49

Tail Light Vinyl Accent Overlay - Gloss Black | 2018-2023 Ford Mustang GT

$29.99
SKU: T-185-GB
Shipping: Calculated at Checkout
Adding to cart… The item has been added

2018-2023 Mustang GT - Gloss Black - Tail Light Overlay

Getting a different look to your Mustang Tail Lights that stands out, is subtle, but still aggressive, may sound tough, but this overlay we have created out of wrap material takes out all the guess work. These unique Vinyl overlays have been pre-cut for easy DIY installation and are made with quality automotive grade vinyl. Unlike most ebay or amazon vendors, Premium Auto Styling vinyl overlays are designed and produced here in the USA in our own facility. We design and test fit all products to ensure fitment guaranteeing you the best results . Basically, if they don’t work on our cars, they’re not going to end up on yours. If you are looking for an inexpensive styling modification, or you just want to change up the factory look, it's a great idea to checkout this vinyl overlay. 

Note: Check with your local laws and regulations before purchase. DISCLAIMER INFORMATION 

INSTALL GUIDE 

TOOLS REQUIRED: ***PRO FELT SQUEEGEE, and HEAT GUN or Warm Sunny Day to Post Heat the product

DRY INSTALL BASICS: Getting the vinyl installed on your vehicle is very easy and only requires minimal tools. For Best results we recommend cleaning the surface that you'll be applying our overlays too, cleaning should consist of removal of any waxes, dirt and or debris. For the cleaning process a clay bar is highly recommended: CLEANING PREP SPRAY & CLAY BAR's SOLD HERE). Before you begin installation of any vinyl overlays please make sure you are working in the right conditions, you should never install vinyl in direct sunlight, never apply vinyl in temperatures that are neither too hot nor too cold. Our in-house expert installers say the optimum temperature for installing vinyl is between 65 and 72 degrees (F). Vinyl can be installed in temperatures as low as 65 degrees (F), and up to 90 degrees (F). Vinyl has a more difficult time conforming and staying in place in colder temperatures though, which is why we recommend waiting until temperatures warm up or install in a temperature controlled environment.

FULL INSTALL: After the surface is clean and you have read and completed "DRY INSTALL BASICS" please note that, this product does take patience and is a multi-piece kit. It is far easier than the single piece alternative but does still take time. Start by identifying the sides and sections of the tail light with the corresponding pieces of the overlay.Install these pieces one at a time.

Start by lining up the side piece product to the outer edge of the face of the light using the corners for reference. As shown in example (A) you want to align the vinyl to the corners of the edge of the tail light about 1-2mm on top of the tail light face. Be very patient with this part as alignment does take time.

You do not need to feed the back edge of the overlay into place at this time, as it will make it more difficult to place. You do not want to place the overlay to high, to low, or to far away from the edge of the face of the tail light otherwise you may be left with a sliver of the tail light visible after applying the final top face piece.

Once placement is set, lay the vinyl starting with the edge that you aligned and gradually pushing the vinyl down with your fingers/ pro-felt squeegee towards the back edge of the side of the tail light evenly across the alignment edge. Be careful not to wrinkle the vinyl, as you are pushing it down, simply lift the back edge back up if you have gone to far on one section causing tension. You should be laying the vinyl into place gradually and evenly.

Once you have throughly removed any and all air from underneath the vinyl using the pro-felt squeegee. Continue these steps for the remaining lights and as a final step, post heat the entire product using a heat gun.

SUPERIOR QUALITY 

• Automotive Grade Adhesive backed vinyl with air release technology for easy installation and removal.

• Includes Driver and Passenger Side Overlays  

• Car wash safe.  

• Can be removed without any damage to surface.  

• 2-5 year life expectancy.  

• Check your local laws and regulations  

>> DISCLAIMER INFORMATION 

DIFFICULTY RATING 3/5

difficulty-rating-3-out-of-5-squeegees-premium-auto-styling.jpg

MORE >> Difficulty Rating Information

Customers Also Viewed