2020-2024 Subaru Outback - Red Out Tail Light Turn Signal Overlay

If you want to really change up the look of the rear end of your Outback and give it a OEM look that no one else has, Red Turn Signals is a great way to start. This overlay is pre-cut to make install DIY friendly. It does take some patience but if you utilize our install kit you can have this drastically different look in no time without even having to leave the garage. This product is made from automotive grade tint film and is made in house here in Riverside California specifically for the 2020 Subaru Outback. We also have a variety of other products for this generation from front to back. Premium Auto Styling vinyl overlays are computer precision cut into durable automotive grade vinyl. This easy peal and stick vinyl accent overlay looks OEM when properly installed. Unlike most ebay or amazon vendors, Premium Auto Styling vinyl overlays are designed and produced here in the USA in our own facility. We design and test fit all products to ensure a perfect fitment guaranteeing you the best results . Basically, if they don’t work on our cars, they’re not going to end up on yours. If you are looking for an inexpensive styling modification, or you just want to change up the factory look, it's a great idea to checkout this vinyl overlay.

Product Note: this is a two piece product made to make installation easier for DIY installers.

INSTALL GUIDE 

WET INSTALL: Getting the vinyl installed on your ride is very easy and only requires minimal tools. What you'll need: lubrication spray solution, squeegee and sometimes a blade and or heat gun. You can make a lubrication spray solution at home by using a spy bottle filled with water and mixing it with 1 drop of dish soap or buy our PRE-MIX SOLUTION SOLD HERE, You'll also need an application squeegee. For Best results we recommend cleaning the surface that you'll be applying our overlays too, cleaning should consist of removal of any waxes, dirt and or debris. For the cleaning process a clay bar is highly recommended: CLEANING PREP SPRAY & CLAY BAR's SOLD HERE). Before you begin installation of any vinyl overlays please make sure you are working in the right conditions, you should never install vinyl in direct sunlight, never apply vinyl in temperatures that are neither too hot nor too cold. Our in-house expert installers say the optimum temperature for installing vinyl is between 65 and 72 degrees (F). Vinyl can be installed as low as 50 degrees (F), and up to 90 degrees (F). 

Let's begin, first start with the bottom piece of the overlay set, and spray the adhesive side of the vinyl very lightly with surface lube. Position the bottom piece by aligning it to the outer edge of the clear portion of the tail light. If positioned correctly there should not be any clear visible along the out edge but you also should not be so far over the edge that the tint bridges the corner onto the red area. Once positioned correctly everything will fall into place correctly. Squeegee this piece into place by applying firm pressure, removing any water and air out from under the tint. Some heat may be required to get the tint to lay correctly. Work all the air and water out to the edges until you get to the inner edge of the tail light where there is a small indent. Pick up the tint in this area and feed it into this indent using your squeegee, heat and then continue. Trim or Tuck the excess tint around the corner of the inner edge. 

Now, take your top piece and align the top corner to the top corner of the bottom piece that follows the outer edge. There will be some overlap of the two pieces. Align the top corner so that the curve from the bottom piece continues as one fluid curve. Once achieved align the rest of the top edge and squeegee into place. Feed tint into indent, same as before. Trim or Tuck Excess around inner edge, same as before. Post Heat Done.

Once you've completed the install we recommend that you leave your car in the sun for up to 30 minutes just to let everything dry, another option would be to use a heat gun to speed up the drying process, known as post heating.  

SUPERIOR QUALITY 

• Adhesive backed film for easy installation and removal.  
• Maintenance free & car wash safe. 
• Can be removed without any damage to surface. 
• 2-5 year life expectancy. 

>> DISCLAIMER INFORMATION 

DIFFICULTY RATING 3/5

MORE >> Difficulty Rating Information