2018-2021 CROSSTREK / IMPREZA 5 DOOR HATCHBACK - Premium Auto Styling bringing you yet another inexpensive way to customize your subie, thanks to our pre cut taillight overlays, Premium Auto Styling's overlays are available in multiple colors for your 2018+ Crosstrek. These accent overlays are constructed from high quality premium cast tint vinyl, and is designed to last several years. As always with all Premium vinyls they are designed and produced right here in house and then tested out on our very own cars first to ensure a perfect fit every time. If you are looking for an inexpensive styling modification, or you just want to change up the factory look, it's a great idea to checkout these overlays.
This product has been updated to Version 2 which includes the extra side piece for full coverage, our version 1 did not cover this area and we are excited to provide an easy DIY solution with our new V2 full stealth kit.
QUICK INSTALL GUIDE: Getting the vinyl installed on your car is very easy and requires just a few tools - A felt edge squeegee will help but is not required and a spray bottle with water inside. Before you begin installing any vinyl overlays make sure your vehicle is cool to the touch - early morning before driving is a perfect time to apply our vinyls. You’ll first want to clean the surface by wiping the area with isopropyl alcohol, Once the surface is clean you are ready for install. Start spraying the adhesive side of the vinyl with a mist of water then position the overlay into place following the taillight lines. Using your finger or felt edge squeegee start from the center and push the air out from underneath the vinyl toward the edges, Minor trimming may be required so have an exacto knife handy. Lastly, remove any excess bubbles then leave your car in the sun for 30 minutes just to let everything settle. This entire process should take you no more than 15 minutes to complete.
For the Turn Signal portion of the install follow these instructions. CLEAN THE LIGHTS SURFACE OF ANY AND ALL DEBRIS. ONCE CLEAN AND DRY, MIST THE SURFACE WITH WATER OR PREMIUM SURFACE LUBE. POSITION THE FACE OVERLAY SO THAT THE OUTERMOST SIDE IS ALIGNED WITH THE EDGE OF THE LIGHT. ONCE POSITIONED TAKE YOUR FELT EDGE SQUEEGEE AND APPLY PRESSURE IN THE CENTER OF THE OVERLAY FROM TOP TO BOTTOM. YOU NOW HAVE YOUR OVERLAY HINGED AND YOU CAN WORK THE WATER OUTWARDS TO EACH SIDE. AFTER THE WATER IS REMOVED OPEN YOUR TRUNK AND TUCK THE EXCESS VINYL INTO THE INNER PART OF THE LIGHT AND THEN HEAT THE OVERLAY WITH YOUR HEAT GUN TO SECURE YOUR EDGES. THE SECONDARY PIECE IS POSITIONED SO THAT THE CORNER OF THE OVERLAY POINTING TOWARDS THE FRONT OF THE VEHICLE IS FLUSH WITH THE LINE THAT MEETS THE UPPER RED PART OF THE TAILLIGHT. ONCE ALIGNED THE MAIN TRIANGLE CAN BE SQUEEGEED DOWN. THE OUTER ARMS OF THE OVERLAY SHOULD NOW BE SET IN PLACE ACROSS THE TOP AND BOTTOM OF THE LIGHT.
DO NOT INSTALL THE VINYL IN DIRECT SUNLIGHT OR IN HIGH TEMPERATURE AREA.
This install is a 3 out 5 in Difficulty.
Difficulty Rating of 1 is used for overlays that are easy for everyone including first time DIYers. (PIECE OF CAKE)
Difficulty Rating of 2 is used when you should expect installations that are easy, but have a few spots that you'll need to take extra care. (NOT TO HARD AT ALL REALLY)
Difficulty Rating of 3 is used for overlays that need just a little time and patience when installing. Extra care is required to help with alignment and getting the film to lay down correctly. (TAKE YOUR TIME YOU'LL BE FINE)
Includes driver and passenger side ( 8 pieces total in the kit )
SUPERIOR QUALITY MATERIALS
• Adhesive backed film for easy installation and removal.
• Maintenance free & car wash safe.
• Can be removed without any damage to lights.
• 1-3 year outdoor life expectancy.
NOTE: Using a felt edge squeegee and a heat gun is highly recommended for this application. Available for purchase in our application tool section above.
Premium Auto Styling
Vinyl Brand Name::