Select your vehicle

Tail Light Reverse Light Overlay - Smoke Tint | 2020 Subaru Outback

Calculated at Checkout
  • Tail Light Reverse Light Overlay - Smoke Tint | 2020 Subaru Outback
  • Tail Light Reverse Light Overlay - Smoke Tint | 2020 Subaru Outback
  • Tail Light Reverse Light Overlay - Smoke Tint | 2020 Subaru Outback
  • Tail Light Reverse Light Overlay - Smoke Tint | 2020 Subaru Outback


2020 Subaru Outback - Smoked Reverse Light Overlay

Looking to just smoke the reverse light section of your tail lights. Perfect, this pre-cut tint overlay does just that. Quality material along with instructions below make for an easy to install DIY product. We also have all the tools you may need for this install as well as any other wrap or tint project you might be trying to accomplish. This product is made in house here in Riverside California specifically for the 2020 Subaru Outback. We also have a variety of other products for this generation Outback from front to back. Premium Auto Styling vinyl overlays are computer precision cut into durable automotive grade vinyl. This easy peal and stick vinyl accent overlay looks OEM when properly installed. Unlike most ebay or amazon vendors, Premium Auto Styling vinyl overlays are designed and produced here in the USA in our own facility. We design and test fit all products to ensure a perfect fitment guaranteeing you the best results . Basically, if they don’t work on our cars, they’re not going to end up on yours. If you are looking for an inexpensive styling modification, or you just want to change up the factory look, it's a great idea to checkout this vinyl overlay.


WET INSTALL: Getting the vinyl installed on your ride is very easy and only requires minimal tools. What you'll need: lubrication spray solution, squeegee and sometimes a blade and or heat gun. You can make a lubrication spray solution at home by using a spy bottle filled with water and mixing it with 1 drop of dish soap or buy our PRE-MIX SOLUTION SOLD HEREYou'll also need an application squeegee. For Best results we recommend cleaning the surface that you'll be applying our overlays too, cleaning should consist of removal of any waxes, dirt and or debris. For the cleaning process a clay bar is highly recommended: CLEANING PREP SPRAY & CLAY BAR's SOLD HERE). Before you begin installation of any vinyl overlays please make sure you are working in the right conditions, you should never install vinyl in direct sunlight, never apply vinyl in temperatures that are neither too hot nor too cold. Our in-house expert installers say the optimum temperature for installing vinyl is between 65 and 72 degrees (F). Vinyl can be installed as low as 50 degrees (F), and up to 90 degrees (F). 

Heat Gun Highly Recommended for install.

After You have read and completed the wet install process you can now start by misting the adhesive side of the overlay as well as the surface you will be applying the overlay to with surface lube (or water with a drop of soap).

Now take the product and begin aligning the bottom edge of the overlay with the bottom edge of the clear portion of the reverse light section on the tail light. Once you have it in place, check top edge alignment before applying any pressure to set it into place. Once placement is confirmed, apply firm pressure with the squeegee on the top portion of the overlay removing any water and air from underneath the tint, working from the center, out.

Then, briefly heat the bottom portion(as shown in the pictures above) of the overlay, continue the squeegeeing process until the overlay is completely installed. Trimming or tucking of excess material required on inner edge of the tail light that faces towards trunk. Either, cut flush to the edge, or heat and tuck the remaining material around the edge. The final look is completely up to you. The final step is to post heat. Heat the entire overlay and check to make sure there is no remaining moisture underneath your overlay.


• Adhesive backed film for easy installation and removal.  
• Maintenance free & car wash safe. 
• Can be removed without any damage to surface. 
• 1-3 year life expectancy. 





MORE >> Difficulty Rating Information


View AllClose