Tail Light Overlay Set - Smoke Tint | 2018-2023 Ford Mustang GT

Name: Tail Light Overlay Set - Smoke Tint | 2018-2023 Ford Mustang GT
SKU: T-129-SMK
Price: 24.99 USD
Availability: InStock

$24.99

SKU: T-129-SMK

Shipping: Calculated at Checkout

Current Stock:

Quantity:

Adding to cart… The item has been added

Description

Description

Tail Light Insert Smoke Tint Overlays | 2018-2023 Ford Mustang GT

The New generation Ford Mustang Tail Lights are some of the most difficult lights to tint, but with this pre-cut kit it just became a lot easier. With a multi-piece pre-cut product for each section of the tail light, all you have to worry about is lining up the product instead of all the difficult harsh bends that previously made this install extremely difficult to conform to the light itself. What is needed is patience and focus to line up the pieces correctly. These unique tint overlays have been pre-cut for easy DIY installation and are made with quality automotive grade vinyl. Unlike most ebay or amazon vendors, Premium Auto Styling vinyl overlays are designed and produced here in the USA in our own facility. We design and test fit all products to ensure fitment guaranteeing you the best results . Basically, if they don’t work on our cars, they’re not going to end up on yours. If you are looking for an inexpensive styling modification, or you just want to change up the factory look, it's a great idea to checkout this vinyl overlay.

INSTALL GUIDE:

TOOLS REQUIRED: ***PRO FELT SQUEEGEE, and HEAT GUN or Warm Sunny Day to Post Heat the product

WET INSTALL BASICS: Getting the vinyl installed on your ride is very easy and only requires minimal tools. What you'll need: lubrication spray solution, squeegee and a heat gun. You can make a lubrication spray solution at home by using a spy bottle filled with water and mixing it with 1 drop of dish soap or buy our PRE-MIX SOLUTION SOLD HERE, You'll also need an application squeegee. For Best results we recommend cleaning the surface that you'll be applying our overlays too, cleaning should consist of removal of any waxes, dirt and or debris. For the cleaning process a clay bar is highly recommended: CLEANING PREP SPRAY & CLAY BAR's SOLD HERE). Before you begin installation of any vinyl overlays please make sure you are working in the right conditions, you should never install vinyl in direct sunlight, never apply vinyl in temperatures that are neither too hot nor too cold. Our in-house expert installers say the optimum temperature for installing vinyl is between 65 and 72 degrees (F). Vinyl can be installed as low as 50 degrees (F), and up to 90 degrees (F).

CONTINUED: After the surface is clean and you have read and completed "WET INSTALL BASICS" please note that, this product does take patience and is a multi-piece kit. It is far easier than the single piece alternative but does still take time. Start by identifying the sides and sections of the tail light with the corresponding pieces of the overlay. Install these pieces one at a time. With the spray bottle lightly mist the surface of the tail light, now start with the side piece first, while the face of the light will be applied second. Lightly mist the adhesive side of the tint piece you are applying first. Line up the side piece to the outer edge of the face of the light using the corners for reference. As shown in example (A) you want to align the vinyl to the corners of the edge of the tail light about 1-2mm on top of the tail light face. Be very patient with this part as alignment does take time. You do not need to feed the back edge of the overlay into place at this time, as it will make it more difficult to place. You do not want to place the overlay to high, to low, or to far away from the edge of the face of the tail light otherwise you may be left with a sliver of the tail light visible after applying the final top face piece. Once placement is set. Now lay the vinyl starting with the edge that you aligned and gradually pushing the vinyl down with your pro-felt squeegee towards the back edge of the side of the tail light evenly across the alignment edge. Be careful not to wrinkle the vinyl, as you are pushing it down, simply lift the back edge back up if you have gone to far on one section causing tension. You should be laying the vinyl into place gradually and evenly. Once you have throughly removed any and all air from underneath the vinyl using the pro-felt squeegee, you can move on to the face of the tail light. Remove the tint from the backing paper, again mist the adhesive side. Align the tint to the same edge of the face of the tail light you aligned the previous too, and adjust if needed. Once placed, with firm pressure start squeegeeing the vinyl down starting from the bottom of the face. Working your way up, until you get to the first crease in the face of the tail light where it bends outwards. Make sure to lay the tint into place up to this point without stretching or warping it. If done correctly, the top of the face of the overlay will simply fall into place. Squeegee the top portion of the overlay at this time, again making sure any and all air and moister has been removed. Continue these steps for the remaining lights and as a final step, post heat the entire product using a heat gun.