Toyota Emblem Overlay - Front Emblem Overlay
Toyota has a great looking front end as is, but what if you could make it better. While making it your own. This is our Stealth emblem overlay, if you're looking for an easy way to change the look of your emblems without all the hassle of taking off the badge itself. These unique Vinyl overlays have been pre-cut for easy DIY installation and are made with quality automotive grade vinyl, not your typical calendar film found in most decal stickers. These overlays have air release technology that allow for easy install. This is the same material we use to wrap entire vehicles. It is a two layer decal. Simple Peel and Stick Process saves you time and money. Unlike most ebay or amazon vendors, Premium Auto Styling vinyl overlays are designed and produced here in the USA in our own facility. We design and test fit all products to ensure fitment guaranteeing you the best results . Basically, if they don’t work on our cars, they’re not going to end up on yours. If you are looking for an inexpensive styling modification, or you just want to change up the factory look, it's a great idea to checkout this vinyl overlay.
NOTE: This overlay has been confirmed from our R&D Vehicle that it does not affect cruise control sensor in the emblem.
2018-2021 Camry (with Radar) Custom Emblem Overlay
2019-2021 Avalon (with Radar) Custom Emblem Overlay
2020-2021 Highlander (with Radar) Custom Emblem Overlay
2017-2021 RAV4 (with Radar) Custom Emblem Overlay
2018-2020 Sienna (with Radar) Custom Emblem Overlay
By purchasing and installing this product, please advise PREMIUM AUTO STYLING does not guarantee the function of collision sensors with use of this product. Buyer assumes all responsibility of any accident caused by use of this product. Although there have no been issues with any sensors, at all times, please drive carefully. All graphics, overlays, and precuts are for offroad use only.
TOOLS REQUIRED: PRO FELT SQUEEGEE, HEAT GUN or Warm Sunny Day to Post Heat the product
DRY INSTALL BASICS: Getting the vinyl installed on your vehicle is very easy and only requires minimal tools. For Best results we recommend cleaning the surface that you'll be applying our overlays too, cleaning should consist of removal of any waxes, dirt and or debris. For the cleaning process a clay bar is highly recommended: CLEANING PREP SPRAY & CLAY BAR's SOLD HERE). Before you begin installation of any vinyl overlays please make sure you are working in the right conditions, you should never install vinyl in direct sunlight, never apply vinyl in temperatures that are neither too hot nor too cold. Our in-house expert installers say the optimum temperature for installing vinyl is between 65 and 72 degrees (F). Vinyl can be installed in temperatures as low as 65 degrees (F), and up to 90 degrees (F). Vinyl has a more difficult time conforming and staying in place in colder temperatures though, which is why we recommend waiting until temperatures warm up or install in a temperature controlled environment.
FULL INSTALL: After the surface is clean and you have read and completed "DRY INSTALL BASICS", remove the vinyl from the backing paper. Hold it by the left and right side and align it to the top edge of the stock emblem. While doing this align the left and right edges, center the overlay and place it on the surface without pushing it down completely. Check to make sure your alignment is correct, if it is not, simply take it back off and align again.
Once placement is confirmed, starting in the center of the emblem, use firm pressure with a pro-felt squeegee and lay the center of the vinyl onto the emblem vertically up and down. Then do the same horizontally.
At this point you have now made a cross and the remaining vinyl to be squeegeed down is in the 4 corners. Do this by starting in the center and working your way outward one corner at a time. Be careful not to make any hard creases, if your placement has caused unnecessary tension using a heat gun may be need to help alleviate that tension.
*This emblem can be installed without any use of heat, but first time installers can have difficulty at times with this step. Simply be patient and do not try to rush.
Once the vinyl is laid completely on the emblem, use the squeegee and run it around the outer edge to tuck any excess you may have if the product was placed to far to one side or the other. This product was created so no trimming should ever be required.
Now, post heat the overlay, simply by letting your vehicle sit out in the warm sun for a approximately 30 minutes, or use a heat gun to speed up the process.
• Automotive Grade Adhesive backed vinyl with air release technology for easy installation and removal.
• Car wash safe.
• Can be removed without any damage to surface.
• 1-3 year life expectancy.
• Check your local laws and regulations
DIFFICULTY RATING 2/5
MORE >> Difficulty Rating Information