"TRX" Logo WINSHIELD BANNER
Stylize your vehicle with our "TRX" Logo Windshield Banner in the following colorway: Gloss Black Banner Base with Gloss Red Logo. This Windshield banner is installed on top of the glass and goes across the top of your windshield similar to a tint strip. -Note this windshield banner may block some of the factory sensors in the top portion of the windshield and cause error messages on the dash.
Premium Auto Styling Overlays are precision cut by our computers using Premium Automotive Grade Films. Unlike other companies, Premium Auto Styling Overlays are designed and produced in the USA in our own facility. We design & fit all of our products to ensure you the best fitment & results. Don't pass up this item to stylize and protect your vehicle!
**Please note that each State/Country has it own laws with placing items on the windshield. Most US states allow items like a tint strip or windshield banner to only go to the "A Line" marking on the windshield. Lower than this A line and you might get a fix it ticket or not pass inspection**
INSTALLATION GUIDE
DRY INSTALLATION: Getting the vinyl installed on your vehicle is very easy and only requires minimal tools.
1. CHECK TEMPERATURE. STANDARD INSTALLATION TEMPERATURE IS 50°F OR 10°C AND ABOVE. YOU WANT TO MAKE SURE YOUR WINDOW IS COOL TO THE TOUCH BEFORE INSTALLING YOUR BANNER. WE RECCOMEND AN ENCLOSED AREA FREE OF AIRBORNE DEBRIS OR STRONG WINDFLOW. AT THE VERY LEAST FIND A SHADED AREA WHERE THE WINDSHIELD CAN COOL DOWN.
2. PREP SURFACE. CLEAN WITH SOAPY WATER AND A MICROFIBER TOWEL. BE SURE TO REMOVE ANY DEBRIS ON THE WINDOW, AS WELL AS THE CREVACES AROUND THE WINDSHIELD. FOR BEST RESULTS CLAY BAR THE SURFACE.
3. DRY SURFACE WITH A CLEAN MICROFIBER TOWEL, REMOVE ALL MOISTURE AND BE SURE TO LIFT UP ANY RUBBER MOLDINGS AND DRY THOSE AREAS AS WELL. AFTER THAT, A QUICK ALCOHOL WIPE BEFORE CONTINUING TO THE NEXT STEP IS BEST. WE RECCOMEND 70% ISOPROPYL ALCOHOL.
4. GRAB A FRIEND. PEEL BACKING PAPER FROM BANNER WHILE THE BANNER IS HELD BY EACH END AWAY FROM THE FLOOR . CENTER THE LOGO TO YOUR WINDSHIELD BY USING YOUR REAR VIEW MIRROR AS A GUIDE. IF IT IS NOT VISIBLE, PLACE A PIECE OF TAPE DOWN AS A CENTER MARKER. THE BANNERS ARE MADE WITH EXCESS MATERIAL ON TOP. THIS IS TO COMPENSATE FOR THE CURVE OF MOST WINDSHIELDS.
5. INSTALL. “GLASS” THE BANNER ACROSS WINDSHIELD BY HOLDING EACH END WITH JUST ENOUGH TENSION TO KEEP THE SURFACE OF THE BANNER SMOOTH. APPLY THE VINYL TO THE SURFACE WITHOUT STRETCHING. YOU WANT TO HOLD THE VINYL TAUGHT BUT DO NOT STRETCH IT. ONCE GLASSED, TACK DOWN THE TOP CORNERS OF THE BANNER TO THE WINDSHIELD.
6. SQUEEGEE. START IN THE MIDDLE OF THE BANNER AND WORK YOUR WAY OUT TO THE EDGES WHILE APPLYING MODERATE PRESSURE. ANY AIR BUBBLES THAT ARRISE SHOULD BE PUSHED TO THE OUTER EDGES OF THE BANNER NEVER BACK TOWARDS THE CENTER. YOU NEVER WANT TO BRIDGE THE MATERIAL ACROSS THE WINDSHIELD OVER ANY TRIMS OR ONTO THE ROOF. YOU WANT TO MAKE SURE YOU PUSH ALL MATERIAL UNDER ANY RUBBER MOLDINGS THAT WILL LIFT UP. FOR CARS THAT DO NOT HAVE ANY TRIM YOU’LL SIMPLY WANT TO GET THE EDGES OF THE BANNER TO LAY AS FLUSH TO ALL THE CORNERS AS POSSIBLE BEFORE TRIMMING
7. TRIM. USING AN EXACTO KNIFE OR NEW SHARP BLADE, YOU WILL WANT TO TRIM THE EXCESS MATERIAL AND TUCK UNDER MOLDINGS AND OR TRIM. VEHICLE MODELS VARY IN MANY DIFFERENT WAYS THE BEST FINISH WILL TYPICALLY COME FROM TUCKING THE VINYL UNDER RUBBER MOLDINGS AND OR TRIM PIECES AFTER THE MAJOR EXCESS HAS BEEN REMOVED. FOR WINSHIELDS WITH LITTLE TO NO TRIMING YOU’LL WANT TO TRIM IN THE NEGATIVE SPACE BETWEEN THE GLASS AND YOUR VEHICLES EXTERIOR. WHILE TRIMMING IN THE NEGATIVE SPACE BE CAREFUL NOT TO COME IN CONTACT WITH YOUR PAINT.
8. CURE. LET THE BANNER CURE IN THE SUN FOR A COUPLE OF HOURS. MOST BANNERS ARE READY TO GO RIGHT AWAY. BUT YOU MAY STILL HAVE TINY AIR BUBBLES LEFT OVER THAT THE SQUEEGEE SIMPLY COULD NOT GET OUT. THE SUN WILL MAKE SURE THE VINYL ADHERES COMPLETELY. THEN YOU’RE DONE.
FEATURES & SPECIFICATIONS
• Includes 1 Precut Sheet of Professional Wrap Film 10" Tall x 60" Wide
• Adhesive backed film for easy installation and removal.
• Maintenance free & car wash safe.
• Can be removed without any damage to surface.
• Please Note, do not use Carnauba Wax on Wrap Films.
• 2-5 year life expectancy.
AVAILABLE COLORS
• Gloss Black Base with Gloss Red Logo
This install is a 2 out 5 in Difficulty.
Difficulty Rating of 2 is used when you should expect installations that are easy, but have a few spots that you'll need to take extra care. (NOT TO HARD AT ALL REALLY)
Excited about your installed Product? Let us know! Take a picture and tag us on Instagram! @premiumautostyling
Interested in a custom color or finish for this product? Contact our team at orders@premiumautostyling.com and we can look into your request before you place your order.
>> DISCLAIMER INFORMATION
